If you are in the process of starting a jewel line, there is a need to know how they are created so that you meet customer demands more effectively. Several methods are involved in making the final products. As long as the methods adhere to unique products are created, and this is what will bring customers to your shop. Below are steps involved in Tufa casting custom jewelry NM.
Stone preparation kicks of the process of creating various jewels. Not every stone can be used in this process but those that are of right size and fits the design of products you intend to produce. Stones should be of good quality. After finding the perfect stones use various tools to smoothen them until they are super smooth. Both sizes should appear super soft, flat and similar to each other.
After the stones have been prepared, it is time to make sketches of what one wants to produce. Sketching takes a lot of time because if errors are made, correcting them again can be costly and time consuming. Therefore, when the sketching process begins one needs to stay in a conducive environment completely.
Use the necessary design tools to carve the stone. There are a couple of tools that one can use in this process such as sewing needles, chisel tools, and wood files. This carving has to be correctly done because once some parts of the stone are cast away, they cannot be reused again. Space which has been created will be used to fill silver fillings to form the piece. Air holes must be left so that when the silver is being poured the process can be achieved very first.
Before silver is poured in the intended space, stones have to be carbonized to get rid of oxygen. The pieces of stones are attached using clamps and rubbers, and this makes the process as perfect as possible. Solid silver is then put in a crucible, and high temperatures of heat are introduced to melt it into an exceptional liquid form. When silver is in its liquid form state, it is then poured on spaces that were left.
Sand is used to smoothening and clean the model. Sand cleans and removes the unwanted parts, and the good news is that the texture is not affected at all. Also, citric acid pickling solution is used in cleaning the surfaces. The pickling solution is effective in removing any traces of fire that are gotten when the soldering process is taking process.
Then polishing is done on the model that has been cleaned using sand. Polishing is aimed at making the design look even more refreshing and attractive. Water can be used, or rubber or even other recommended polishing compounds. The compound range from abrasive to non abrasive, and for every stage of polishing different compounds are used.
On completion of most processes, the products are almost ready for the market. Although they are available, there is room for designers to put various styles on them before they are sold. This can be done keeping mind your target market and what you intended to create. As much as other stages take a lot of time, sanding and polishing take the most time.
Stone preparation kicks of the process of creating various jewels. Not every stone can be used in this process but those that are of right size and fits the design of products you intend to produce. Stones should be of good quality. After finding the perfect stones use various tools to smoothen them until they are super smooth. Both sizes should appear super soft, flat and similar to each other.
After the stones have been prepared, it is time to make sketches of what one wants to produce. Sketching takes a lot of time because if errors are made, correcting them again can be costly and time consuming. Therefore, when the sketching process begins one needs to stay in a conducive environment completely.
Use the necessary design tools to carve the stone. There are a couple of tools that one can use in this process such as sewing needles, chisel tools, and wood files. This carving has to be correctly done because once some parts of the stone are cast away, they cannot be reused again. Space which has been created will be used to fill silver fillings to form the piece. Air holes must be left so that when the silver is being poured the process can be achieved very first.
Before silver is poured in the intended space, stones have to be carbonized to get rid of oxygen. The pieces of stones are attached using clamps and rubbers, and this makes the process as perfect as possible. Solid silver is then put in a crucible, and high temperatures of heat are introduced to melt it into an exceptional liquid form. When silver is in its liquid form state, it is then poured on spaces that were left.
Sand is used to smoothening and clean the model. Sand cleans and removes the unwanted parts, and the good news is that the texture is not affected at all. Also, citric acid pickling solution is used in cleaning the surfaces. The pickling solution is effective in removing any traces of fire that are gotten when the soldering process is taking process.
Then polishing is done on the model that has been cleaned using sand. Polishing is aimed at making the design look even more refreshing and attractive. Water can be used, or rubber or even other recommended polishing compounds. The compound range from abrasive to non abrasive, and for every stage of polishing different compounds are used.
On completion of most processes, the products are almost ready for the market. Although they are available, there is room for designers to put various styles on them before they are sold. This can be done keeping mind your target market and what you intended to create. As much as other stages take a lot of time, sanding and polishing take the most time.
About the Author:
Get a summary of the things to keep in mind when choosing a tufa casting custom jewelry NM designer and more information about an experienced designer at http://www.bojoejewelry.com now.
ليست هناك تعليقات:
إرسال تعليق